Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 15 / 148

Spectrophotometer Basics

Selecting and Positioning Cuvettes

Thermo Scientific

269-289800

6-Position Cell Holder

Single Cell Holder

See the parts list for a more detailed list of available accessories.

Selecting and Positioning Cuvettes

The compatible wavelength range for different types of cells depends on the material used.

Note

If the Cell Positioner method option is set to Auto 6, whenever you press

Run Test

to start a measurement, the instrument attempts to initialize the cell positioner. If a single
cell holder is installed, the message “Error, Single Cell Holder found. Use Single Cell
Holder?” appears. Press

Accept Change

to continue the measurement with a single cell, or

install the 6-cell changer and press

Cancel Change

Cell Type

Wavelength

Optical Glass
Borosilicate Glass

360 nm to > 1100 nm
330 nm to > 1100 nm

Disposable:
Quartz
Polystyrene
Methacrylate
Acrylic
UV-transparent

190 nm to > 1100 nm
> 340 nm
> 300 nm
> 280 nm
> 220 nm

Note

See the manufacturer’s specifications and work within the recommended range.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды