Thermo Scientific Orion AquaMate 7000 Vis Скачать руководство пользователя

Страница: 105 / 148

Concentration Measurements—Standard Curve Application

Editing a Standard Curve

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis



To measure samples manually (using Manual 6 or Single Cell Holder)

1. Press

Run Test

2. Install the blank and samples.

3. Press

Measure Blank

If a 6-Position Cell Holder is installed, it moves to the B position to measure the blank
and returns to its previous position.

4. Press

Measure Samples

If a 6-Position Cell Holder is installed, press the cell position buttons to reposition the cell
holder and measure the rest of the samples manually.

When the instrument has measured all the samples, the Standards screen shows the
absorbance and concentration of each sample.

Editing a Standard Curve

You may edit the concentration of any standard on a standard curve. In addition, you may
change the number of standards, select a different curve fit or delete points from the curve.

Содержание Orion AquaMate 7000 Vis





















































































































































Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды

Thermo Scientific Orion AquaMate 7000 Vis, Руководство пользователя

Результаты поиска

Содержание Orion AquaMate 7000 Vis

Отзывы:

Похожие инструкции для Orion AquaMate 7000 Vis

Бренды по названию

Популярные бренды