Thermo Scientific LTQ XL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 176

background image

1

Introduction

What Types of Experiments Can I Perform with the LTQ XL MS Detector?

16

LTQ XL Getting Started

Thermo Electron Corporation

What Types of

Experiments Can I

Perform with the LTQ

XL MS Detector?

This topic describes several types of experiments that you can perform with
the LTQ XL MS detector. The experiments can be grouped into the
following categories:

• General MS or MS

n

• Data-Dependent™

• Ion Mapping™

• Ion Tree

You can specify which type of experiment you want to perform in the
Instrument Setup window, and then save it in an Instrument Method
(.METH) file.

General MS or MSn

Experiments

You can use a General experiment to collect qualitative data for structural
analysis. The Xcalibur data system includes an Instrument Method template
in Instrument Setup so you can get started with a General MS or MS

n

experiment. For an example of a General MS or MS

n

experiment template,

see

In a General

MS

experiment, you need to specify the mass range of your

analyte(s) of interest. In a General

MS/MS

experiment, you need to specify a

parent (precursor ion) that fragments into distinctive product ions. In a
General

MS

n

experiment, you need to specify the mass-to-charge ratios of

all

the parent ions of interest. The LTQ XL MS detector can then collect data
on the ions in the range or on the product ions of the parent ion(s) that you
specify.

If you use a General experiment to collect data for qualitative (structural)
analysis, you specify the scan mode (MS through MS

n

) for which you want

data in the Scan Event Settings group box. If you specify MS/MS or MS

n

,

you then choose the parent ion(s) for which you want data in the MS

n

Settings table. The LTQ XL MS detector can then collect distinct qualitative
information for structural analysis or for spectral reference.

Note

Procedures for these experiments are beyond the scope of this

LTQ

XL Getting Started

manual. If you need more information, refer to online

Help.

«
...
26
27
28
29
30
...
»

Содержание LTQ XL

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LTQ XL

SACE Tmax XT Series

Бренд: ABB Страницы: 11

Бренд: GALLERY Страницы: 18

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренд: HABYS Страницы: 16

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды