Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 56 / 442

background image

1

Performing Routine Maintenance

Replacing a Column

28

ISQ 7000 Hardware Manual

Thermo Scientific

b. On the ISQ 7000 Dashboard set the MS transfer line temp to 40 °C and the ion

source temp to 175 °C (to avoid excessive oxidation of source parts or contamination
from the V-lock source plug).

2. Using the source removal tool and vacuum interlock, remove the ion source cartridge. See

the

ISQ 7000 Hardware Manual

for instructions to remove the ion source cartridge.

3. Place the ion source cartridge on the source holder and set aside.

4. Place the V-lock source plug in the source plug holder.

5. Attach the source exchange tool to the V-lock source plug in the source plug holder.

6. Twist the plug until it aligns securely in the grooves in the source exchange tool and

remove the plug from the holder. The V-lock source plug is securely attached to the
source exchange tool when the alignment grooves on each piece match up.

Figure 21.

Attaching the V-lock Source Plug to the Source Exchange Tool

7. Once the ion source temperature has dropped below 200 °C, insert the barrel end of the

source exchange tool into the vacuum interlock and twist it clockwise to lock the source
exchange tool into position. Be sure the black handle remains fully extended and locked.

8. Evacuate the VPI.

a. Confirm that the source removal tool is properly engaged in the VPI.

b. Press the blue

Evacuate

button on the front of the instrument.

c.

The

Evacuate

light will begin to flash green, and should continue to flash green for

approximately 20 seconds.

9. If the pressure has returned to an acceptable value after the 20-30 second wait, the

evacuate light will turn off and the

Ready to Open

light will be solid green. At that point,

Note

Use compressed air to blow all the dust off the V-lock source plug before inserting it

into the mass spectrometer.

Note

If the ion source temperature is above 200 °C, parts of the ion source or the V-lock

source plug could oxide and be damaged, causing leaks in the MS system.

Alignment Grooves

«
...
54
55
56
57
58
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Charge Analyzer 711

Бренд: 3M Страницы: 24

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Cablescan Страницы: 58

SourceMeter 2400

Бренд: Keithley Страницы: 594

System SourceMeter 2601B

Бренд: Keithley Страницы: 864

Бренд: Labgear Страницы: 8

SourceMeter 2600B Series

Бренд: Keithley Страницы: 897

Бренд: National Instruments Страницы: 12

Бренд: Macnaught Страницы: 8

Бренд: YATO Страницы: 36

Бренд: Van Walt Страницы: 2

Бренд: Aqualytic Страницы: 130

Бренд: Danfoss Страницы: 16

Бренд: Ibravebox Страницы: 32

Бренд: Omega Страницы: 100

Бренд: Ocean Reef Страницы: 24

Бренд: YZXStudio Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды