Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 394 / 442

Advanced Maintenance

Replacing the Calibration Gas Components

366

ISQ 7000 Hardware Manual

Thermo Scientific

5. Remove the glass manifold cover.

6. Set the glass manifold cover on a clean work surface and protect from dust.

7. Use a 5/16 in. wrench to disconnect the stainless steel tubing from the two connectors on

each side of the transfer line.

Figure 415.

Removing the Glass Manifold Cover

Note

If you are using CI gas, there are two tubes connected. If you are using an EI system,

there is one tube and one blanking ferrule connected.

Figure 416.

Disconnecting the Transfer Line Tubing

Glass Manifold Cover

Connectors

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды