Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 32 / 442

Performing Routine Maintenance

Maintenance Supplies and Tools

ISQ 7000 Hardware Manual

Thermo Scientific

Maintenance Supplies and Tools

To perform routine maintenance on the ISQ 7000 mass spectrometer, you will need the
following supplies and tools.

Table 1.

Items in the MS Toolkit (Order if you have an instrument with no VPI

Item

Included in the
MS Toolkit

Not Included in
the MS Toolkit

Cloth or paper, lint-free

✓

Column measuring tool

✓

Small source exchange tool

✓

Forceps

✓

Gas, clean and dry

✓

Gloves, clean, lint-free

✓

Protective eyewear

✓

Torx® T10 screwdriver

✓

Torx® T20 screwdriver

✓

Torx® T30 screwdriver

✓

Wrenches, open-ended, 1/4-in., 5/16-in., 3/8 in.,
7/16-in.

✓

Note

The tools in the MS Toolkit are shipped in a black plastic case with the instrument.

Each tool in the kit can be ordered separately or you can order an additional toolkit. See
the

ISQ and TSQ GC-MS Spare Parts Guide

for ordering information.

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды