Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 256 / 442

Advanced Maintenance

Replacing Components of the Vacuum Interlock

228

ISQ 7000 Hardware Manual

Thermo Scientific

15. Flip the block over in your hand so that sealing ball and outer ball seal will fall out. Set

them aside or replace them, if necessary.

16. Pry the thin metal clip out of the groove. It holds all of the other components inside the

valve body.

CAUTION INSTRUMENT DAMAGE:

The sealing ball must not be scratched, so be very

careful when handling it and keep it on a clean, lint-free surface.

ATTENTION DOMMAGES À L’INSTRUMENT

: la bille d’étanchéité ne doit pas être rayée,

soyez donc très prudent lorsque vous la manipulez et maintenez-la sur une surface propre et
non pelucheuse.

Figure 227.

Replacing the Sealing Ball and Outer Ball Seal

Figure 228.

Replacing the Metal Clip

Sealing Ball

Outer Ball Seal

Clip

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды