manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

3

 Advanced Maintenance

Replacing Components of the Analyzer

162

ISQ 7000 Hardware Manual

Thermo Scientific

6. Hold the quadrupole in the tray and make sure the quad assembly and the ion guide are 

correctly positioned before tightening the screws on the entrance lens endcap

7. Reattach the screws on each side of the exit endcap. Make sure the quadrupole and exit 

endcap are fully forward before tightening screws.

8. Attach the wire connecting the quadrupole entrance lens to the source interface board by 

screwing in the terminal with a slotted screwdriver.

Replacing the Analyzer Tray

To replace the analyzer tray

1. Put tray in manifold with transfer line out or pulled away.

a. If the gas tubes are attached to the transfer line, it will not pull as far away from the 

path of the tray as would be best. Be extra careful not to scratch the end of 
transferline with the tray, because that could cause a leak with the source plug later.

b. Do not screw in the analyzer tray until the transfer line is fully screwed in.

Figure 132. 

Reattaching the Quadrupole and Ion Guide to the Analyzer Tray

Screws

Exit Endcap

Entrance Endcap

Note  

The analyzer tray will mount on one alignment pin in the back and the transfer line 

on the right. The mixing chamber will rest on the transfer line when installed.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

ABB LevelMaster 7100 Quick Start preview
LevelMaster 7100
Бренд: ABB Страницы: 2
ABB 4690 Series Upgrade Procedure preview
4690 Series
Бренд: ABB Страницы: 4
ABB SACE Emax 2 Owner'S Manual preview
SACE Emax 2
Бренд: ABB Страницы: 20
Utilitech CMG-102 Care And Maintenance preview
CMG-102
Бренд: Utilitech Страницы: 2
TaiDoc L1 Owner'S Manual preview
L1
Бренд: TaiDoc Страницы: 31
Yamaha 141 Quick Operation Manual preview
141
Бренд: Yamaha Страницы: 2
Bacharach MGS-401 User Manual preview
MGS-401
Бренд: Bacharach Страницы: 19
Bante Instruments PHscan10 User Manual preview
PHscan10
Бренд: Bante Instruments Страницы: 6
Balluff BML-S1G0-Q71 Series Condensed Manual preview
BML-S1G0-Q71 Series
Бренд: Balluff Страницы: 20
Teledyne Lecroy BPA Quick Start Manual preview
BPA
Бренд: Teledyne Lecroy Страницы: 3
X-Rite DensiEye 700 Quick Start Manual preview
DensiEye 700
Бренд: X-Rite Страницы: 130
Endress+Hauser 11362Z Safety Instructions preview
11362Z
Бренд: Endress+Hauser Страницы: 24
Omega FMG490 Series User Manual preview
FMG490 Series
Бренд: Omega Страницы: 24
Winland EnviroAlert EA200 Quick Start Manual preview
EnviroAlert EA200
Бренд: Winland Страницы: 3
TESTO 0560 3164 Quick Start Manual preview
0560 3164
Бренд: TESTO Страницы: 2
janitza UMG 605 Operating Manual preview
UMG 605
Бренд: janitza Страницы: 92
Befaco BF22 User Manual preview
BF22
Бренд: Befaco Страницы: 3
Midtronics EBT-965P User Manual preview
EBT-965P
Бренд: Midtronics Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды