Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 162 / 442

background image

2

Troubleshooting

Investigating Vacuum Issues

134

ISQ 7000 Hardware Manual

Thermo Scientific

An air leak has been detected.

Foreline pump will not power-on.

Foreline pump powers on, but the system will not pump down.

Turbomolecular pump will not power-on.

Possible Remedies

Spray gas around the vacuum manifold and look for characteristic ions in full-scan EI mode. Correct any problems. Some of the most
common ways to address leaks are:

•

Tighten the transfer line nut or union.

•

Tighten the vent valve knob.

•

Make sure there is clean helium flow from the GC.

•

Evacuate the region between the vacuum interlock knob and sealing ball by pressing the

Evacuate

button.

•

Check the transfer line or inlet ferrules. Replace them if they are broken. See

for details.

•

Clean dust or debris from the top cover O-ring.

If you do not find a leak, turn on the ISQ 7000 system in full-scan mode, open Manual Tune, select the real-time viewer and scan the mass
range that covers the characteristic ions for the compressed gas you are using. Most compressed gases have ions between m/z 35 and
100. While you are reviewing the ions, spray the gas around the components in the bulleted list above. When you see the characteristic
ions in the real-time viewer, the component you just sprayed has a leak and needs to be addressed.

Possible Remedies

If the Vacuum light on the front of the instrument is flashing amber quickly, the system took too long to reach vacuum and shut off. You
must cycle the power on the ISQ 7000 instrument to enable the foreline pump to power-on.

Make sure the foreline pump switch is in the On position.

Make sure the cable from the foreline pump to the ISQ 7000 instrument is properly attached to the MECH PUMP connector on the back of
the ISQ instrument.

Configure the foreline pump for the proper line voltage.

Make sure the ISQ system is properly connected to an electrical outlet and is powered on.

Possible Remedies

Tighten the vent valve knob.

Check the vacuum connection of the last component you performed maintenance on and make sure it is sealed properly.

Tighten the clamps and connectors on the foreline hose. Replace the foreline hose if it is damaged.

Check the level of the foreline pump oil and, if necessary, add more oil. See

Adding Oil to the Foreline Pump

Possible Remedy

Check the foreline pump and plumbing for leaks to ensure the fore pressure is low enough for use. You can check the convectron gauge
readback to confirm the foreline pressure falls to less than 1 Torr.

«
...
160
161
162
163
164
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Omicron Страницы: 80

Бренд: Samsara Страницы: 16

Бренд: bmcm Страницы: 5

Бренд: Tektronix Страницы: 48

Бренд: janitza Страницы: 128

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: SOMFY Страницы: 40

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Бренд: Ramsey Electronics Страницы: 40

Cobra SMARTsense Ammonium Ion 12913-00

Бренд: PHYWE Страницы: 5

Бренд: Water I.D. Страницы: 56

Бренд: Meec tools Страницы: 23

NetSure M832DNA

Бренд: Vertiv Страницы: 176

Бренд: J&D Electronics Страницы: 2

Бренд: POSEIDON Страницы: 13

Бренд: ICP DAS USA Страницы: 71

Бренд: CONDTROL Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды