Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 10 / 442

background image

Low Voltage Safety Compliance

This device complies with Low Voltage Directive 2011/95/EC.

FCC Compliance Statement

Notice on Lifting and Handling of

Thermo Scientific Instruments

For your safety, and in compliance with international regulations, the physical handling of this Thermo Fisher Scientific
instrument

requires a team effort

to lift and/or move the instrument. This instrument is too heavy and/or bulky for one

person alone to handle safely.

Notice on the Proper Use of

Thermo Scientific Instruments

In compliance with international regulations: Use of this instrument in a manner not specified by Thermo Fisher
Scientific could impair any protection provided by the instrument.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION

Read and understand the various precautionary notes, signs, and symbols

contained inside this manual pertaining to the safe use and operation of this product before
using the device.

ATTENTION

Lisez et comprenez les différentes précautions, ainsi que les signes et symboles de

ce manuel relatifs à l’utilisation sûre de ce produit, avant d’utiliser le dispositif.

«
...
8
9
10
11
12
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: Camille Bauer Страницы: 11

Бренд: Camille Bauer Страницы: 83

Бренд: OHAUS Страницы: 84

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: X-laser Страницы: 17

Бренд: Hanna Instruments Страницы: 28

Бренд: KROHNE Страницы: 56

Бренд: Percussion Play Страницы: 3

Бренд: horiba Страницы: 27

Бренд: Dräger Страницы: 538

Бренд: Sonel Страницы: 84

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: TA Instruments Страницы: 68

Бренд: ScienTECH Страницы: 44

Бренд: PKP Страницы: 7

Бренд: Hanna Instruments Страницы: 52

Бренд: geo-FENNEL Страницы: 32

Бренд: Level 1 Lasers Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды