Thermo Scientific Ion Torrent A45727 Скачать руководство пользователя страница 157

Страница: 157 / 163

Safety standards

Reference

Description

EU Directive 2014/35/EU

European Union “Low Voltage Directive”

IEC 61010-1
EN 61010-1
UL 61010-1
CAN/CSA C22.2 No.

61010-1

Safety requirements for electrical equipment for measurement, control, and laboratory

use – Part 1: General requirements

IEC 61010-2-010
EN 61010-2-010

Safety requirements for electrical equipment for measurement, control and laboratory

use – Part 2-010: Particular requirements for laboratory equipment for the heating of

materials

IEC 61010-2-020
EN 61010-2-020

Safety requirements for electrical equipment for measurement, control and laboratory

use – Part 2-020: Particular requirements for laboratory centrifuges

IEC 61010-2-081
EN 61010-2-081

Safety requirements for electrical equipment for measurement, control and laboratory

use – Part 2-081: Particular requirements for automatic and semi-automatic

laboratory equipment for analysis and other purposes

IEC 61010-2-101
EN 61010-2-101

Safety requirements for electrical equipment for measurement, control and laboratory

use - Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical

equipment

EMC standards

Reference

Description

EU Directive 2014/30/EU

European Union “EMC Directive”

EN 61326-1
IEC 61326-1

Electrical Equipment for Measurement, Control and Laboratory Use – EMC

Requirements – Part 1: General Requirements

EN 61326-2-6
IEC 61326-2-6

Electrical equipment for measurement, control and laboratory use. EMC requirements.

Particular requirements. In vitro diagnostic (IVD) medical equipment

FCC Part 18 (47 CFR)

U.S. Standard “Industrial, Scientific, and Medical Equipment”

AS/NZS CISPR 11

Limits and Methods of Measurement of Electromagnetic Disturbance Characteristics of

Industrial, Scientific, and Medical (ISM) Radiofrequency Equipment

ICES-001, Issue 4

Industrial, Scientific and Medical (ISM) Radio Frequency Generators

FCC Part 15 Subpart B (47

CFR)

U.S. Standard Radio Frequency Devices
This equipment has been designed and tested to CISPR 11 Class A. In a domestic

environment it may cause radio interference, in which case, you may need to take

measures to mitigate the interference.
Do not use this device in close proximity to sources of strong electromagnetic radiation

(e.g. unshielded intentional RF sources), as these can interfere with proper operation.

Appendix E

Safety

Safety and electromagnetic compatibility (EMC) standards

Genexus

™

Integrated Sequencer User Guide

157

Содержание Ion Torrent A45727




































































































































































Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды

Thermo Scientific Ion Torrent A45727, Руководство пользователя

Результаты поиска

Содержание Ion Torrent A45727

Отзывы:

Похожие инструкции для Ion Torrent A45727

Бренды по названию

Популярные бренды