Thermo Scientific Invitrogen E-Gel A33811 Скачать руководство пользователя страница 25

Страница: 25 / 59

E-Gel

™

Power Snap Electrophoresis System User Guide

E-Gel

™

CloneWell

™

II gels

E-Gel

™

CloneWell

™

II pre-cast agarose gels are designed for use with the E-Gel

™

Power Snap Electrophoresis Device,

and provide a fast, safe, and effective DNA fragment isolation method for DNA cloning workflows.

Advantages

•

Target fragments are collected directly from a recovery well. No gel-purification is required.

•

Contains SYBR

™

Safe DNA stain, eliminating the risk of DNA damage, and improving cloning

efficiency by avoiding UV transillumination.

General
guidelines

•

Load gel within 15 minutes of opening the pouch; run the gel immediately after loading.

•

Monitor the band of interest carefully as it migrates near the recovery wells. It may be difficult
to see low amounts of DNA in the well.

•

Important!

Always wear Safe Imager

™

Viewing Glasses when viewing the gel with the filter

lid opened.

•

For guidance on disposal of used gels, see SYBR

™

Safe DNA Gel Stain (page 48).

Prepare samples

•

Prepare  up to  25 μL  of  sample in  1X  Sample Loading  Buffer (e.g., use 2.5 μL of 10X Sample
Loading Buffer with 22.5 μL total sample).
10X  Sample Loading  Buffer is  provided with E-Gel

™

Clonewell

™

II Agarose Gels.

•

Use the indicated amount of DNA per well

for single or multiple bands.

•

Divide samples with higher amounts of DNA across multiple wells.

•

Use up to 25 μL total sample volume per well.

•

Dilute high salt samples (certain restriction enzyme and PCR buffers) 2- to 5-fold.

Gel type

Amount of DNA per well

Total loading

volume

Sample with single band

Sample with multiple bands

E-Gel

™

CloneWell II

200-800 ng

800 ng

25 μL

Prepare gel

Remove

the gel from the package.

Gently

remove

the combs. Do not allow the

combs to bend or create suction in the
wells during removal.

Insert

gel cassette into the E-Gel

™

Power

Snap Electrophoresis Device, starting from
the right edge.

Press down on the left side of the cassette
to secure it into the device.

Содержание Invitrogen E-Gel A33811




























































Результаты поиска

Содержание Invitrogen E-Gel A33811

Отзывы:

Похожие инструкции для Invitrogen E-Gel A33811

Бренды по названию

Популярные бренды

Thermo Scientific Invitrogen E-Gel A33811, Руководство пользователя

Результаты поиска

Содержание Invitrogen E-Gel A33811

Отзывы:

Похожие инструкции для Invitrogen E-Gel A33811

Бренды по названию

Популярные бренды