Thermo Scientific iCAP RQ ICP-MS Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 71

background image

General Pre-Installation Information

Installation

Thermo Scientific

iCAP RQ Pre-Installation Requirements Guide (P/N BRE0009927, Revision A)

6-3

Installation

It is the policy of Thermo Fisher Scientific that the customer should not
unpack the system or accessory items prior to installation of the system.

NOTICE

Where buck/boost transformers or power conditioning units

are supplied, it is the responsibility of the operator to have these units
installed by an electrician prior to instrument installation.

▲

NOTICE

A forklift or a pallet jack will be of great benefit for unpacking

and in-house transportation of the instrument components.

▲

Installing the System

When your new instrument is on site and ready for installation, a
Thermo Fisher Scientific field service engineer will install it.

During the installation, the Thermo Fisher Scientific field service
engineer will demonstrate the following:

•

The basics of equipment operation and routine maintenance.

•

The performance specifications that are in force at the time of the
purchase of the system.

NOTICE

Consumables sent with the system are intended for use by the

Thermo Fisher Scientific field service engineer during the installation.

▲

Key Operator

Experience has shown that the maximum benefit can be derived from a
scientific instrument if there is one person, a key operator, who has
major responsibility for that instrument. Thermo Fisher Scientific
recommends that you designate a key operator to oversee the operation
and maintenance of the system in your laboratory. The key operator
should be available to the installing engineer throughout the
installation. This person will also be the key figure in the
communication between your laboratory and Thermo Fisher Scientific.

NOTICE

Do not plan to use your new system for sample analysis until

the installation is complete and the Acceptance Form has been signed.

▲

«
...
56
57
58
59
60
...
»

Содержание iCAP RQ ICP-MS








































































Отзывы:

Нет отзывов

Похожие инструкции для iCAP RQ ICP-MS

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Panasonic Страницы: 174

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

BODY ARMOR PRO TERM

Бренд: Darco Страницы: 6

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: HANYOUNG NUX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды