Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 59

Страница: 59 / 134

Basic Concentration Measurements—Basic A-%T-C

Using Conc/Factor to Measure Concentration

Thermo Scientific

GENESYS 10S Vis User Guide

2. Press

Measure Blank

If the Single Cell Changer is installed, remove the blank and place the standard in the cell
changer.

3. Press

Units/Standard

to set the units and measure the standard.

4. Press

Enter Conc

, enter the concentration value of the standard and press

Enter

5. Press

Select Units

, highlight the appropriate unit in the list and press

Enter

6. Press

Measure Standard

The instrument measures the absorbance of the standard and displays the absorbance and
calculated factor.

Using Conc/Factor to Measure Concentration

In this mode a concentration factor is used to determine the concentration of samples. The
concentration of unknown samples is determined ratiometrically from the entered factor. The
measurement can be expressed mathematically as

(Abs / %T of Sample) * Factor = Concentration of Sample

where the factor is entered, the Abs/%T of the sample is measured, and the sample
concentration is calculated.

To use Conc/Factor to measure concentration

1. If necessary, press

Change Mode

to switch to the Conc With Factor mode.

2. Press

Units/Factor

to set the factor and select the units.

3. Press

Enter Factor

4. Type the desired factor value.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды