Thermo Scientific GENESYS 10S Vis Скачать руководство пользователя страница 14

Страница: 14 / 134

Spectrophotometer Basics

Z-dimensions

GENESYS 10S Vis User Guide

Thermo Scientific

Other Guidelines

Position cuvettes and test tubes so that the clear sides face the light beam, one clear side facing
the front of the instrument and the other facing the back.

When using small aperture (small volume) cells:

• Always used cells with black masking

• Use the same cell (or cuvette) for your blank and your samples

Z-dimensions

The figure below illustrates the position of the light beam in the instrument.

Beam size specifications are shown below.

• Distance from bottom of cuvette to center of beam (Z-dimension): 8.5 mm

• Beam dimensions: 2 mm (wide) by 7 mm (tall)

Note

The pathlength of test tubes is not as well defined as that of square cuvettes.

Note

Always place test tubes in the instrument in exactly the same orientation in the light

beam. An alignment mark on the test tube helps you orient the test tubes consistently and
correctly.

Содержание GENESYS 10S Vis







































































































































Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды

Thermo Scientific GENESYS 10S Vis, Руководство пользователя

Результаты поиска

Содержание GENESYS 10S Vis

Отзывы:

Похожие инструкции для GENESYS 10S Vis

Бренды по названию

Популярные бренды