Thermo Scientific Dionex Easion Скачать руководство пользователя страница 83

Страница: 83 / 126

5 • Service

Doc. 155028-01 08/20

To install the new backup piston seal:

1. Lift the spacer off the pump head.

2. Remove the seal holder from the spacer, using one of the following methods:

•

With the seal holder facing up, cup the spacer
in your hand and blow clean laboratory air at
the spacer to dislodge the seal holder.

–or–

•

Insert a thin object or pointed tool into the
small notch on the spacer and carefully pry out
the seal holder.

Be careful not to scratch the

spacer

3. Insert a thin object (for example, the straightened end of a paper clip) into the

spacer and carefully pry the backup piston seal out of the spacer.

Be careful

not to scratch the spacer

Figure 5-7. Secondary Pump Head

Notch

Seal
Holder

Spacer

Содержание Dionex Easion































































































































Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды

Thermo Scientific Dionex Easion, Руководство оператора

Результаты поиска

Содержание Dionex Easion

Отзывы:

Похожие инструкции для Dionex Easion

Бренды по названию

Популярные бренды