manualshive.com logo in svg

Thermo Scientific DensityPRO+, Руководство по установке

Поделиться
Скачать
Thermo Scientific DensityPRO+ Скачать руководство пользователя страница 40

Wiring 

Power Supply Wiring 

Power to the 

Transmitter 

When connecting power to the 1400A/1400S transmitters, refer to 
installation wiring drawing 

868680-2

. 

Note  

To meet the requirements of CSA 1010.1, an external switch or 

circuit breaker must be installed to allow the power source to be 
disconnected from the gauge. In addition, protective bonding (grounding) 
must always be provided even if a DC power source is used. 

▲

  

With AC power, the 1400A and 1400S transmitters are designed to operate 
on 100–240 Vac, at an input frequency of 50/60 Hz. The same system 
configuration can be directly wired to either 115 or 230 Vac. The 
maximum input power requirement is 12 VA when all options are present. 

AC Power 

Connections are shown in the table below. 

Table 

 

4–3. 

AC power wiring for 1400A/1400S transmitters 

AC Power Supply  

Transmitter 

L J1-L 

N J1-N 

 

DC Power 

Note

  To meet the requirements of CSA 1010.1, the input DC terminals 

must be supplied from an SELV (Safety Extra Low Voltage) source. 

▲

 

With 24 Vdc power, the 1400A and 1400S transmitters are designed to 
operate on 20–28 Vdc. The maximum input power requirement is 12 VA 
when all options are present.  

Connections are shown in the table below. 

Table 

 

4–4. 

24 Vdc power wiring for 1400A/1400S transmitters 

+24Vdc Power Supply  

Transmitter 

+24Vdc 

J5-8 (+24Vdc input) 

+24Vdc return 

J5-9 (GND) 

 

 

 

4-10

     Den Installation Guide 

Thermo Fisher Scientific 

Содержание DensityPRO+












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды