Thermo Scientific DensityPRO Скачать руководство пользователя страница 49

Страница: 49 / 101

Chapter 8

Diagnostics

This chapter provides on the Diag/Service menu in the NI-FBUS
Configurator root menu. The Diag/Service menu provides access to the
Current Output, Loop Test, Trim Analog Output, Device Status, and
AI_Transducer Parameters items.

Note

If you are not using the NI-FBUS Configurator, reference the

documentation that came with your host system.

▲

Note

This chapter provides instructions using the NI-FBUS Configurator

menus, as this is the preferred way to configure the instrument. Move from
one step to the next in the configurator method window by clicking

Next

or pressing

Enter

. If your host does not support menus, reference

Appendix

for a list of DensityPRO parameters.

▲

Note

For detailed discussion on any of the diagnostic items discussed,

reference the DensityPRO user guide (P/N 717784).

▲

Current Output

The steps below describe how to configure the current output.

Go to

AI_TRANSDUCER > Root Menu > 6 Diag/Service > 1

Current Output > Current output setup.

When prompted, remove the loop from automatic control.

Max current output:

Enter the maximum current output (between 0

and 20.5 mA).

Min current output:

Enter the minimum current output (between 3.8

and 20 mA).

Current output hold mode value:

Enter the hold mode value for the

current output. The value is entered as a percentage of the maximum
current output.

Thermo Fisher Scientific

DensityPRO with

OUNDATION

™ fieldbus

Application Guide

8-1

Содержание DensityPRO






































































































Результаты поиска

Содержание DensityPRO

Отзывы:

Похожие инструкции для DensityPRO

Бренды по названию

Популярные бренды

Thermo Scientific DensityPRO, Инструкция по применению

Результаты поиска

Содержание DensityPRO

Отзывы:

Похожие инструкции для DensityPRO

Бренды по названию

Популярные бренды