Thermo Scientific Cryofuge 5500i GMP Скачать руководство пользователя страница 58

Страница: 58 / 114

Operation

Selecting the temperature

You can select the temperature in the range of -9 °C

to +40 °C.
(Please consult the standard diagram in the appendix

to obtain the attainable values.)
To adjust the temperature, proceed as follows:
1. Press one of the “set” keys

(for an increase) or

(for a decrease) in the “temperature” section of

the control panel once to switch from the actual to

the set value mode.

2. By

briefly

pressing the input key you can now

raise or lower the run time in 1°

steps.

3. If you keep the selected key pressed, the display

changes continuously and slowly at first and then

in accelerated paces up or down.

4. Release the key as soon as you have reached the

desired value, and adjust if necessary by repeat-

edly pressing the key.

The temperature display flashes for a few seconds,

then changes to the actual value mode. The tempera-

ture set value is stored now.

Pretemp function

The Pretemp function permits easy and quick pretem-

perature-regulation of the unloaded rotor.
Upon calling this function by actuating the key

, all

you have to do is to enter the desired temperature.
After actuating the start key , the rotor temperature

is equalized within 30 respectively 60 minutes at the

speed defined in the pretemp function.

Содержание Cryofuge 5500i GMP



















































































































Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды

Thermo Scientific Cryofuge 5500i GMP, Инструкция по эксплуатации

Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды