Thermo Scientific BF51634BC-1 Скачать руководство пользователя страница 35

Страница: 35 / 78

Thermo Scientific

6-1

Operation - UP550 Controller

Figure 4. UT150 Control Panel.

The following instructions are very basic and meant to provide the minimum

amount of information to get you started. Please read the appendix and the UP550

Short Form Instruction Manual to more fully understand the capabilities of this

control.

UP550 Controller

The UP550 temperature controller is a microprocessor-based PID-type controller

that can store up to 30 programs (programs are also referred to as patterns) with

up to 99 segments each or a single program of up to 300 segments. rn addition to

operating as a programmable controller with "ramps and dwells", it can also

operate as a single setpoint unit in the LOCAL mode.

First, you will need to be informed about the various modes of operation that are

available. The green LED next to the lower display shows the mode the control is

in at any given time.

Содержание BF51634BC-1















































































Результаты поиска

Содержание BF51634BC-1

Отзывы:

Похожие инструкции для BF51634BC-1

Бренды по названию

Популярные бренды

Thermo Scientific BF51634BC-1, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BF51634BC-1

Отзывы:

Похожие инструкции для BF51634BC-1

Бренды по названию

Популярные бренды