Thermo Scientific ARL EQUINOX 5000 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 58

background image

Chapter |

Installation

Confidential, limited rights

PN AA83865 | Revision A | 25-Oct-2019

Instruction Notice, ARL EQUINOX 5000-5500

Page

36

6.4.4 ARL EQUINOX 5000/5500: Installation of an External Gas Cylinder

The gas regulator has to be mounted on the gas cylinder (be careful, the thread is
anti-clockwise). If the gas regulator is not shipped with the instrument, it is the responsibility
of the user to obtain and install the regulator locally as well as a safety valve (preloaded to
max 6.5 bar) on the input gas circuit to avoid any overpressure inside of the instrument.

A feedthrough with a female quick fitting is located on the back panel
and labeled “GAS IN”.

A short hose with a 6 mm diameter with a male quick fitting already
mounted is shipped with the instrument.

Connect the hose to the gas regulator. The connector is a standard
Swagelok gas connector.

1.

Open the gas cylinder and slightly open the gas regulator in order to have a small gas
flow.

2.

Connect the long hose male fitting in the input re

ceptacle “GAS IN” located on the back

panel.

3.

Adjust the outlet gas pressure on the regulator to the recommended value (6 bar).

If the gas pressure is set to a too high value, the gas output “OUT” on the detector has to be
disconnected and it will be used to decrease the gas pressure. To decrease the pressure,
close the gas regulator and insert but not completely the male quick fitting of the output gas
hose of the detector. Let some gas to flow for a few second. Increase the pressure again by
opening slowly

the gas regulator. Remount the output gas hose on the “OUT” connector on

the detector.

«
...
34
35
36
37
38
...
»

Содержание ARL EQUINOX 5000



























































Отзывы:

Нет отзывов

Похожие инструкции для ARL EQUINOX 5000

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: Baker Instrument Company Страницы: 24

Бренд: Ecco Страницы: 3

Бренд: XanLite Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: EuroLite Страницы: 28

Бренд: Quivogne Страницы: 13

Бренд: Yetter Страницы: 24

Бренд: U-Line Страницы: 6

Бренд: Ultratune Страницы: 12

Бренд: EzCAP Страницы: 15

NTP TECHNOLOGY DAD Thunder Core 256

Бренд: DAN Страницы: 16

Бренд: Major tech Страницы: 12

Бренд: Dangerous power Страницы: 38

IQAN-LC5-C0 Series

Бренд: Parker Страницы: 40

SOLID PLUS HEAT

Бренд: Rotaid Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды