Thermo Scientific Agilent 1200 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 58

background image

2

Setting Up the LAN Interface

Setting the Stored TCP/IP Address for the LAN Interface

14

Agilent 1200 Series Getting Connected Guide for LC Devices

Thermo Scientific

Figure 13.

Telnet session with the LAN Status Page

b. If the stored IP address is not set to 172.16.0.102, type

ip 172.16.0.102

, and then

press ENTER.

c.

If the stored subnet mask is not set to 255.255.0.0, type

sm 255.255.0.0

, and then

press ENTER.

d. To verify the IP address and subnet mask settings, type a slash (/), and then press

ENTER to display the current settings of the LAN interface.

8. To exit the Telnet session, do one of the following:

• For the on-board LAN interface, type

exit

at the prompt.

–or–

• For the LAN card, type

quit

at the prompt.

quit

Saves changes and exits the shell (for the G1369 LAN card).

exit

(Model G1369 LAN card) Exits the Windows command line
without saving the changes.
(On-board LAN interface) Saves the changes and exits the
Windows command line.

Table 2.

Telnet commands (Sheet 2 of 2)

Value

Description

IP address and
subnet mask for
an Agilent LC/
Thermo Scientific
MS system

Agilent default
IP address

«
...
24
25
26
27
28
...
»

Содержание Agilent 1200 Series



























































Отзывы:

Нет отзывов

Похожие инструкции для Agilent 1200 Series

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Unex Страницы: 5

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Nakayama Страницы: 14

Бренд: Tar River Страницы: 26

Бренд: ZOLL Страницы: 38

Бренд: ZOLL Страницы: 36

Nature2 Fusion soft

Бренд: Zodiac Pool Systems Страницы: 52

Бренд: G21 Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды