Thermo Scientific A55867 Скачать руководство пользователя страница 163

Страница: 163 / 198

System error list

Code

Message

Context

Description

Recovery action

0x8855

Unknown
initialization error

Startup

Error was detected
during instrument
startup

Export service logs
and send to tech
support for further
assistance

0x8857

Unable to decrypt
upgrade package

Upgrade

Unable to decrypt
the software update
package

Export service logs
and send to tech
support for further
assistance

0x8860

Package is not
suitable for this
instrument

Upgrade

Software update file
is not compatible
with instrument

Export service logs
and send to tech
support for further
assistance

0x8861

Instrument class
is not supported
by this upgrade
package

Upgrade

Software update file
is not compatible
with instrument

Export service logs
and send to tech
support for further
assistance

0x8865

Unable to power up
instrument

Startup

Error was detected
during power up
sequence

• Power cycle

and check if
the instrument
can self
recover

• Export service

logs and send
to tech support
for further
assistance

0x8867

Unable to recover
from upgrade failure

Upgrade

Error was detected
when trying to
recover from an
interrupted software
update

• Ensure that

power is not
turned OFF
during software
update

• Retry software

update,
contact tech
support if error
persists

0x8870

Emergency stop
activated at startup

Startup

Emergency stop
was active at
startup

Reset emergency
stop switch and
perform a power
cycle on the
instrument

Appendix B

Error lists

System error list

CTS

™

DynaCellect

™

Magnetic Separation System User Guide

163

Содержание A55867







































































































































































































Результаты поиска

Содержание A55867

Отзывы:

Похожие инструкции для A55867

Бренды по названию

Популярные бренды

Thermo Scientific A55867, Руководство пользователя

Результаты поиска

Содержание A55867

Отзывы:

Похожие инструкции для A55867

Бренды по названию

Популярные бренды