Thermo Scientific 42iQD Скачать руководство пользователя страница 230

Страница: 230 / 286

Servicing

DMC Ozonator

7-40

42iQD Instruction Manual

Thermo Scientific

Use the following procedure to replace the ozonator and transformer board,

and to replace the flow switch.

●

Removing the ozonator and transformer

●

Replacing the ozonator and transformer board

●

Replacing the flow switch

Use the following procedure to remove the ozonator and transformer.
Equipment Required:

Phillips drive, #2

Turn the instrument OFF, unplug the power cord, and remove the

cover (

Figure 2–1

Unplug converter DMC (J2) and flow pressure board (J4).

Figure 7–44.

HVPS, Electrical

DMC Ozonator

Ozonator and

Transformer

Removal

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды