Thermo Scientific 42iQD Скачать руководство пользователя страница 216

Страница: 216 / 286

Servicing

DMC PMT Cooler and Reaction Chamber Replacement

7-26

42iQD Instruction Manual

Thermo Scientific

Use the following procedure to replace the PMT cooler and clean or

replace the reaction chamber assembly.

●

Remove the PMT Cooler

●

Replacing the PMT board

●

Removing and Cleaning the Reaction chamber

●

Replacing the PMT Cooler and Reaction chamber

●

PMT Replacement

Use the following procedure to remove the PMT cooler from the

instrument.
Equipment Required:

Phillips drive, #2

Turn the instrument OFF, unplug the power cord, and remove the

cover (

Figure 2–1

Make sure the PMT has cooled down before touching.

▲

Unhook plumbing by pulling loop downwards and unhook tubing.

Using a #2 Phillips drive, unfasten two 6-32 flat head screws.

Pull shroud outwards.

DMC PMT Cooler

and Reaction

Chamber

Replacement

PMT Cooler Shroud

Removal

Icon Here

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды