manualshive.com logo in svg

Thermo Scientific 42iQD, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific 42iQD Скачать руководство пользователя страница 152

Operation 

Settings 

3-128

     42iQD Instruction Manual 

Thermo Scientific 

 

The Update Bootloader screen allows the user to update bootloader and 

reboot the instrument. The bootloader is a small program that interfaces 

with our hardware and runs our operating system on power-up. The 

bootloader may change to optimize hardware settings or if there are 

changes to the hardware. If the button is blue, an update to the bootloader 

is available. If button is greyed out, no update is needed. 

Home Screen>Settings>Update Bootloader

 

 

The Update Bootloader screen contains the following information: 

●

 

Reboot and Update:

 Update bootloader and reboot instrument. 

●

 

Exit:

 Exits screen. 

 
 

Update Bootloader 

Содержание 42iQD































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды