Thermo Scientific 42iQD Скачать руководство пользователя страница 100

Страница: 100 / 286

Operation

Settings

3-76

42iQD Instruction Manual

Thermo Scientific

The Gas Units screen defines how the NO

concentration readings are

expressed. The µg/m

, mg/m

, and g/m

gas concentration modes are

calculated using a standard pressure of 760 mmHg and a standard

temperature of 0 °C. The temperature can be changed in the compensation

screen.
Use the



and



buttons to select.

Home Screen>Settings>Measurement Settings>Gas Units

The Gas Units screen contains the following information:

●

ppb:

parts per billion.

●

ppm:

parts per million.

●

percent.

●

µg/m3:

micrograms per meter cubed.

●

mg/m3:

milligrams per meter cubed.

●

g/m3:

grams per meter cubed.

Gas Units

Содержание 42iQD































































































































































































































































































Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQD, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQD

Отзывы:

Бренды по названию

Популярные бренды