Thermo Scientific 1300 Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 130

background image

1300 Series A2 3-3

Thermo Scientific

Section 3

Start-Up

Unlock

Counterweight

The window counterweight is secured to the back of the cabinet to protect
it from damage during shipping.

Caution

The counterweight on

the cabinet back compensates for
the weight of the front window.
Do not try to move the front
window before the counterweight
has been unlocked.

s

Warning

After unlocking, keep

hands and fingers away from the
motion range of the
counterweight!

s

To unlock the counterweight,
remove the shipping screws
(see location arrows in Figure 3-2)
and retain them for future
shipping needs. A Torx wrench is
shipped in the manual bag for
this purpose.

Warning

One person should hold the counterweight while a second

person removes the screws. This facilitates screw removal and avoids the
possibility of stripping the screws.

s

Note

The cabinet should be leveled only after it has been located in the

desired working location.

s

For cabinets without a stand, place a bubble level onto the work tray
surface and adjust the cabinet until the level indicates an absolutely
horizontal position in all directions.

For cabinets with an optional stand, place a bubble level onto the work
tray and adjust the four levelers of the stand using an open end or
adjustable wrench until the bubble level indicates an absolutely horizontal
position in all directions. Check from right to left, and from back to front.

Level the Cabinet

Counterweight

Figure 3-2.

Unlocking the Counterweight

«
...
26
27
28
29
30
...
»

Содержание 1300 Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1300 Series

Бренд: GE Страницы: 138

Бренд: Vahle Страницы: 96

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Xtool Страницы: 8

Бренд: Additel Страницы: 107

Бренд: EFX Страницы: 2

Бренд: EuroLite Страницы: 2

Бренд: Ublox Страницы: 22

Бренд: Ignis Pixel Страницы: 4

Deep Root Planter 1.8m

Бренд: Zest 4 Leisure Страницы: 5

Бренд: Faro Страницы: 161

Бренд: Griven Страницы: 36

Бренд: Pixlip Страницы: 15

Бренд: Cooper Lighting Страницы: 1

Бренд: Energetics Страницы: 89

Бренд: Transpak Страницы: 9

Бренд: Telecast Страницы: 16

Бренд: Festo Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды