Thermo Scientific 074114 Скачать руководство пользователя | Manualshive

Страница: 15 / 148

background image

1 • Introduction

Doc. 065378-01 1/12

7

1.4

Safety and Regulatory Information

The Dionex PDA was manufactured by Thermo Fisher Scientific at the following
location: 527 Lakeside Drive, Sunnyvale, CA 94088-3603 U.S.A. The Dionex
PDA is designed for use with IC (ion chromatography), BioLC

®

(biocompatible

liquid chromatography), and HPLC (high-performance liquid chromatography)
systems and should not be used for any other purpose. Operation of the Dionex
PDA in a manner not specified by Thermo Fisher Scientific may result in personal
injury.

If there is a question regarding appropriate usage, contact Technical Support for
Dionex products. In the U.S. and Canada, call 1-800-346-6390. Outside the U.S.
and Canada, call the nearest Thermo Fisher Scientific office.

1.4.1

Safety Messages and Notes

This manual contains warnings and precautionary statements that can
prevent personal injury and/or damage to the Dionex PDA when properly
followed. Safety messages appear in bold type and are accompanied by
icons, as shown below.

Messages d’avertissement en français

Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may
result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.

Indicates that the function or process of the instrument may be
impaired. Operation does not constitute a hazard.

Signale une situation de danger immédiat qui, si elle n'est pas évitée,
entraînera des blessures graves à mortelles.

«
...
13
14
15
16
17
...
»

Содержание 074114





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 074114

Бренд: 3M Страницы: 88

Бренд: +360 Страницы: 9

Бренд: EverFocus Страницы: 12

Бренд: RED SHIELD Страницы: 25

Бренд: Vicon Страницы: 28

Бренд: Q-See Страницы: 9

Бренд: C&K systems Страницы: 6

Бренд: Idis Страницы: 16

MarCell MAR-A-500

Бренд: Sensored Life Страницы: 2

Бренд: Abus Страницы: 2

Бренд: C.P. Electronics Страницы: 8

ELI-SIP2-APTZ8-R30X

Бренд: e-Line Technology Страницы: 42

Бренд: Lloyd's Страницы: 24

Бренд: Dahua Technology Страницы: 56

Бренд: Surveon Страницы: 116

Бренд: Dahua Страницы: 17

Бренд: Okina USA Страницы: 2

Бренд: OPTICOM Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды