background image

 

i

 

I.  SAFETY SECTION 
 
This  page  contains  various  warnings  and  cautions  found  throughout  the  Oil  Furnace 
Manual. Please read and comply with the statements below.
 
 
 

c

WARNING AND CAUTIONS: 

 

c

WARNING: This furnace is not to be used as a construction heater. See Page 1. 

 

c

  CAUTION  MUST  BE  TAKEN  NOT  TO  EXCEED  90°  ROTATION  (OF  THE  FLUE 

ELBOW) COUNTERCLOCKWISE OR RIGHT FROM THE VERTICAL POSITION. 
See Page 2.
 
 

c

WARNING:  The predetermined  limit location on this oil fired furnace has been tested 

and  approved  by  Thermo  Products,  LLC.  Any  attempt  to  relocate  this  safety  control  or 
replace  this  safety  control  with  a  control  that  is  not  approved,  or  is  incompatible,  may 
result in personal injury, substantial property damage or death.  See Page 5. 
 

c

WARNING:  THE  HEAT  EXCHANGER  MUST  BE  CLEANED  BY  A  QUALIFIED 

SERVICE  PERSON. See Page 8. 
 

c

CAUTION: DO NOT ATTEMPT TO MAKE REPAIRS YOURSELF! See Page 9. 

 

c

WARNING: The area around the furnace should be kept free and clear of combustible 

liquids and  material, especially papers and rags. See Page 9. 
 

c

WARNING: NEVER burn garbage or refuse in your furnace. Never try to ignite oil by 

tossing burning papers or other material into your furnace. See Page 9. 
 

c

WARNING: This oil furnace is designed to burn No. 1 or No. 2 distillate fuel oil. NEVER 

USE GASOLINE OR A MIXTURE OF OIL AND GASOLINE. See Page 9. 

 

c

CAUTION:  DO NOT ATTEMPT TO START THE BURNER WHEN: 

1. Excess oil has accumulated, 
2. The furnace is full of vapors  

 3. The combustion chamber is very hot. 
 IF ONE OR MORE OF THESE CONDITIONS EXIST, CONTACT A QUALIFIED 
SERVICE PERSON. See Page 9. 
 

Содержание Spirit VHF-ABE





















Отзывы: