background image

 

 

GAS FIRED HIGH EFFICIENCY FURNACE 

DOWN FLOW & DIRECT VENT (SEALED COMBUSTION) 

 

MODEL: CMA1-50N & CMA2-75N 
INSTALLATION AND SERVICE MANUAL

 

For installation in:  

1.  

Manufactured Homes 

2.  

Modular Homes/Buildings 

3.  

Site Constructed—Residential (Single Story Dwellings) 

  

 

 

FOR YOUR SAFETY 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this 
or any other appliance.

 

 

WHAT TO DO IF YOU SMELL GAS 

•  

Do not try to light any appliance.

 

•  

Do not touch any electrical switch; do not use any phone in your building. 

•  

Immediately call your gas supplier from a neighbor’s phone.  

    Follow the gas supplier’s instructions.

      

•  

If you cannot reach your gas supplier, call the fire department.

 

 

 

:

 If the information in these instructions is not followed exactly, a fire or explosion may 

result causing property damage, personal injury, or loss of life. 
 

: Improper installation, adjustment, alteration, service, or maintenance can cause 

injury or property damage.  Refer to this manual.  For assistance or additional information, 
consult a qualified installer, service agency, or fuel supplier. 
 

Do not use this appliance if any part has been underwater.  Immediately call a 

qualified service technician to inspect the appliance and to replace any part of the electrical or 
control system that has been underwater. 
 

 

 

 

 

 

 

 

 

 

 

 

THERMO PRODUCTS, LLC. 

                                       POST OFFICE BOX 217 

     NORTH 

JUDSON, 

IN 

46366

 

 

 

 

 

 

PHONE: (574) 896-2133 

 

 

 
MG-508   

ECN 5135-MA 100615

 

MADE IN USA 

 

 

 

 

 

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE 
PERFORMING ANY SERVICE OR MAINTENANCE.  THESE INSTRUCTIONS MUST BE LEFT WITH THE USER 
AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY QUALIFIED SERVICE PERSONNEL.

Содержание CMA1-50N
























































Отзывы: