background image

Refrigeration Maintenance

78

Charging the System

1. Insure that all compartment bulkheads are 

open. Ceiling mounted bulkheads should not 
be stored close to the evaporator outlets as this 
will restrict airflow.

2. Determine the correct charge for the unit as 

configured. The actual weight of the charge 
may vary somewhat due to length of 
refrigerant lines.

3. The unit should still be in Evacuation mode. 

Add as much of the charge as possible as 
liquid through the discharge service valve and 
receiver tank outlet valve.

4. Back seat and crack the discharge service 

valve.

5. Back seat the receiver tank outlet valve.

6. Crack the suction service valve.

7. Exit the Evacuation mode by turning the 

Zone1/Host On/Off switch Off, and then back 
On.

8. Turn all zones On and set all zone setpoints 

for the lowest possible temperature to insure 
that all zones run in Cool mode. Allow the 
unit to start.

9. Cover the condenser as required to maintain 

discharge pressure from 325 to 400 psig (2241 
to 2758 kPa) and add the remaining charge by 
weight as liquid through the suction service 
valve.

10. If necessary, continue to add refrigerant until 

the ball in the receiver tank sight glass is 
floating but is no higher than 1/2 way up the 
glass. If they system is overcharged, remove 
refrigerant until the ball in the receiver tank 
sight glass is floating but is no higher than 1/2 
way up the glass.

11. Continue to operate the unit and monitor the 

sight glass until all compartment temperatures 
are at or below 0 F (-18 C).

12. If the receiver tank sight glass level drops, add 

additional refrigerant as required to maintain 
refrigerant in the bottom 1/2 of the sight glass.

13. When refrigerant level is correct back seat all 

service valves, remove the gauge manifold, 
and securely replace valve stem covers with 
seals and service port caps before returning 
the unit to service.

Содержание Spectrum DE 30-2













































































































































Отзывы: