Thermia Atria Optimum Скачать руководство пользователя страница 48

Страница: 48 / 76

Menu selection

Meaning

Factory setting

CURVE 0

Local increase or reduction of CURVE at an outdoor temperature of 0°C. Shown in the

graph for CURVE.

0°C(range: -5°C /

5°C)

CURVE -5

Local increase or reduction of CURVE at an outdoor temperature of -5°C. Shown in the

graph for CURVE.

0°C(range: -5°C /

5°C)

HEAT STOP

Maximum outdoor temperature when heat production is permitted.

If HEAT STOP applies, the outdoor temperature must drop 3°C below the setting before

HEAT STOP stops.

17°C(range:

0°C / 40°C)

REDUCTION

Only appears if the tariff control function has been activated. Lowering set room temper-

ature. Active at 10 kΩ connection at EVU input.

2°C(range: 1°C /

10°C)

TANK TEMP

Displayed if buffer tank is active. Charges the buffer tank to the set temperature. AUTO

setting charges the tank to the supply line setpoint value.

AUTO(range:

AUTO, 30°C /

55°C)

OVERCHARGE

Displayed if the buffer tank is active and TANK TEMP is set to AUTO. Charges the buffer

tank to supply line setpoint value + the value of OVERCHARGE.

0°C(range: 0°C /

5°C)

ROOM FACTOR

Only displayed if an accessory Room temperature sensor is installed.

Determines how great an impact the room temperature is to have when calculating the

supply temperature. For under floor heating it is recommended that ROOM FACTOR is set

to 1, 2 or 3. For radiator heating it is recommended that ROOM FACTOR is set to 2, 3 or 4.

(0 = no impact, 4 = very large impact).

2(range: 0 / 4)

POOL (Expansion card)

Only appears if POOL is selected. The temperature in the pool is controlled by a separate

sensor regardless of the heating and hot water system.

20°C(range:

5°C /40°C)

POOL HYSTERESIS (Ex-

pansion card)

Only appears if POOL is selected. The difference between the desired charge value (ad-

justable) and actual value to the pool sensor. Pool hysteresis does not affect the integral

value.

2°C(range: 1°C /

10°C)

8.3

Sub-menu HEAT CURVE 2

Only appears if shunt group sensor is connected and activated in menu SERVICE -> INSTALLATION - SYSTEM -> SHUNT GROUP.

Menu selection

Meaning

Factory setting

CURVE 2

Calculated shunt group temperature at 0°C outdoor temperature. Shown as a graphic

curve. The curve will be limited by the set values of MIN and MAX.

40°C(range:

22°C / 56°C)

MIN

Minimum permitted shunt group temperature, if the temperature for heat stop has not

been reached.

10°C(range:

10°C / 50°C)

MAX

Maximum permitted shunt group temperature.

55°C(range:

15°C / 70°C)

8.4

Sub-menu TEMPERATURE

The history of different temperature measurements can be viewed by pressing the right arrow key. The graph shows the last 60 meas-

urement points for the set time interval (SERVICE -> INSTALLATION -> LOG TIME). In the event of an alarm, history stops being logged

until the alarm is reset by changing the operating mode to OFF.

Menu selection

Meaning

Factory setting

OUTDOOR

Shows the actual outdoor temperature.

ROOM

Shows the actual set temperature.

SYSTEM SUPPLY

Displays system supply temperature at the buffer tank system.

SUPPLY LINE

Shows the actual supply temperature. The calculated supply temperature to the heating

system group is within brackets.

During hot water production in operating mode AUX. HEATER the value for HOT WATER

STOP + 10° is shown within brackets.

Installation Guide

Domestic heat pumps

VMGFP202

Thermia Värmepumpar

Содержание Atria Optimum













































































Результаты поиска

Содержание Atria Optimum

Отзывы:

Похожие инструкции для Atria Optimum

Бренды по названию

Популярные бренды

Thermia Atria Optimum, Руководство по установке

Результаты поиска

Содержание Atria Optimum

Отзывы:

Похожие инструкции для Atria Optimum

Бренды по названию

Популярные бренды