Thermia Atria Optimum Скачать руководство пользователя страница 44

Страница: 44 / 76

6.7

Selection of system solution and connection of external aux. heater

6.7.1

Introduction

Configure the heat pump for the desired system solution in the SERVICE\ADD. HEATER\EXTERNAL ADDITION

menu.

Also see section Piping installation.

6.7.2

System solution 1

The heat pump is delivered configured for system solution 1.

6.7.3

System solution 2

If necessary the external components must be fused using accessory 086U9685 FUSE TO EXTERNAL COMPO-

NENT according to the installation instructions supplied with the accessory. The tables below give the compo-

nents referred to.

For system solution 2, select the following in menu SERVICE\AUX. HEATER\EXT.AUX.HEATER:

▪

EXT.AUX.HEATER = ON

▪

REV.V. HOT WATER = INT

For Diplomat, Diplomat Optimum, Diplomat Optimum G2/G3, Diplomat Duo, Diplomat Duo Optimum, Diplomat Duo Optimum G2/G3,

and Comfort Optimum, the electrical connection for system solution 2 must be carried out according to the following table:

Component

Connection

Internal immersion heater

I/O-card, output for 6 kW (normal connection)

External auxiliary heater

I/O-card, output for 3 kW, connected and fused with 086U9685

Additional shunt

Terminal block, 215/216

Internal exchange valve

I/O-card, 214 (normal connection)

For Atria Optimum Atria Duo Optimum, the electrical connection for system solution 2 must be carried out according to the following

table:

Component

Connection

Internal immersion heater

I/O-card, output for 3 kW and 6 kW as well as Defrost card, output for 6 kW (normal connections)

External auxiliary heater

Defrost card; 283, connected and fused with 086U9685

Additional shunt

Terminal block, 215/216

Internal exchange valve

I/O-card, 214 (normal connection)

Installation Guide

Domestic heat pumps

VMGFP202

Thermia Värmepumpar

Содержание Atria Optimum













































































Результаты поиска

Содержание Atria Optimum

Отзывы:

Бренды по названию

Популярные бренды

Thermia Atria Optimum, Руководство по установке

Результаты поиска

Содержание Atria Optimum

Отзывы:

Бренды по названию

Популярные бренды