background image

Amazon HXINUV, Installation Instructions A1, 28th June 2019

About Thermal Integration

About Us

We design and manufacture pre-fabricated Hot Water and Central Heating Cylinders, Thermal Stores, Buffer Tanks and Heat Interface
Units to suit almost any domestic or commercial application. Our range of products is the end result of over 20 years of continuous
development and improvement in heating technology. We hold to the philosophy that all customers deserve our best level of service for
the life of the product, as well as complete honesty throughout the product selection process. We hold a significant number of patents
in the fields of water storage, heat exchange, and the networking of communal heating systems, and continue to push the boundaries.

As well as the most comprehensive range of hot water systems in the UK, our headquarters in Sudbury also offers the UKs largest
renewables training centre, including the first HETAS training and test centre, with working wood, pellet and log biomass rigs, as well
as solar. There is also an extensive district heating demonstration and test facility attached to the factory, with the factory building
services running from a twin pellet biomass boiler installation, buffer storage, and HIUs to provide services. The entire facility is
controlled using our in-house 

IHIU Control Systems

 that allow any of our products to be network connected, with online monitoring and

dashboard facilities.

For a complete history of the company please read 

History of Thermal Integration Limited

 on Heatweb Wiki.

Product Range

Heat Interface Units
Standard Cylinders
Shortened Cylinders
Buffer Cylinders
Combination Cylinders
Mains Pressure Thermal Stores
Mains Hot Water Conversion Kits
Prefabricated Systems
Plate Heat Exchangers
Boiler Conversion Kits
Control Systems

Knowledge Base

To make the dissemination of technical material as simple as possible, we publish all our documentation through an online document
storage system, the 

Heatweb Wiki

. Links to further information may be found throughout documents.  

Useful Contacts

Commercial Sales and Operations: 0845 2411441
Specflue Sales: 0333 9997974

Web Sites

 

http://www.heatweb.co.uk

 Company Website

 

http://www.systemdesigner.co.uk

 System Designer

 

http://wiki.heatweb.com/wiki

 Heatweb Wiki

 

http://www.heatweb.info

 Monitoring software and online APIs

Page 3

Содержание Amazon HXINUV
















Отзывы: