Thermal Dynamics A80 CUTMASTER Скачать руководство пользователя страница 28

Страница: 28 / 130

A80

INSTALLATION

0-4985

3-2

A. Cover Removal

1. Remove the upper and lower screws which secure

the cover to the main assembly. Do not loosen the

lower screws inside the cut out slots in the bottom

of the cover.

NOTE!

The upper screws and lower screws are

not the same. Do not mix them. The upper

screws are for threading into the plastic of

the front and rear panels. DO NOT use the

finer threaded lower screws for this.

Art # A-08429

Lower

Screws

Lower

Screws

Slots

Upper

Screws

2. Carefully pull the Cover up and away from the unit.

B. Cover Installation

1. Reverse previous procedures for cover installation.

NOTE!

When installing the upper screws, attempt to

reuse the original threads. The easiest way

to do this is by turning the screw counter-

clockwise until you feel the threads line up,

then begin to turn the screw clockwise to

tighten. Do not over tighten.

C. Input Power Selection

Set the Input Voltage Selection Switch at the rear of the unit

based on the primary input voltage it is connected to. Low

is 208/230 VAC and high is 460 VAC.

Art # A-08316

D. Quick Guide to Phase Wiring

The following illustration and directions are for changing
phase of the power supply.

Art # A-08493

Input Power Cable Connections

Three-Phase (3ø)

Store copper jumpers on base plate

Single-Phase (1ø) and Jumper Settings

GND

L3
L4

GND

L3
L4

Single and Three Phase Input Power Wiring

NOTE!

There are two jumpers used for the single

phase 230V setting and none for three phase.

E. Connections to Single Phase Input Power

WARNING

Disconnect input power from the power

supply and input cable before attempting

this procedure.

These instructions are for changing the input power and or

cable on the 208/230, 400, 460 VAC Power Supply to Single

- Phase input power.

1. Remove the Power Supply cover.

See "A. Cover Removal".

2. Disconnect the original input power cable from the

main input contactor and the chassis ground con-

nection.

3. Loosen the through - hole protector on the back

panel of the power supply. Pull the original power

cable out of the power supply.

4. If the power cable being used is not the factory -

supplied cable, use a three - conductor input power

cable for the voltage desired and strip back the

insulation on the individual wires.

Содержание A80 CUTMASTER



































































































































Результаты поиска

Содержание A80 CUTMASTER

Отзывы:

Thermal Dynamics A80 CUTMASTER, Руководство по эксплуатации, Страница: 28 / 130

Результаты поиска

Содержание A80 CUTMASTER

Отзывы: