Thermal Dynamics A80 CUTMASTER Скачать руководство пользователя страница 31

Страница: 31 / 130

A80

0-4985

INSTALLATION

3-5

Using High Pressure Air Cylinders

When using high pressure air cylinders as the air supply:

1. Refer to the manufacturer’s specifications for instal-

lation and maintenance procedures for high pres-

sure regulators.

2. Examine the cylinder valves to be sure they are clean

and free of oil, grease or any foreign material. Briefly

open each cylinder valve to blow out any dust which

may be present.

3. The cylinder must be equipped with an adjustable

high - pressure regulator capable of outlet pressures

up to 100 psi (6.9 bar) maximum and flows of at least

300 scfh (141.5 lpm).

4. Connect supply hose to the cylinder.

NOTE!

Pressure should be set at 100 psi (6.9 bar) at

the high pressure cylinder regulator.
Supply hose must be at least 1/4 inch

(6 mm) I.D.
For a secure seal, apply thread sealant to the

fitting threads, according to manufacturer's

instructions. Do Not use Teflon tape as a

thread sealer, as small particles of the tape

may break off and block the small air pas-

sages in the torch.

Installing Optional Two - Stage Air Filter Kit

This optional two - stage air line filter is also for use on

compressed air shop systems. Filter removes moisture and

contaminants to at least 5 microns.

Connect the air supply as follows:

1. Attach the Two Stage Filter bracket to the back of

the power supply per instructions supplied with the

filter assembly.

NOTE!

For a secure seal, apply thread sealant to the

fitting threads, according to manufacturer's

instructions. Do not use Teflon tape as a

thread sealer, as small particles of the tape

may break off and block the small air pas-

sages in the torch.

2. Connect the two stage filter outlet hose to the inlet

port of the Regulator / Filter Assembly.

3. Use customer - supplied fittings to connect the air

line to the Filter. A 1/4 NPT to 1/4" hose barbed fit-

ting is shown as an example.

Regulator

Input

Gas Supply

Hose

1/4 NPT to 1/4”

(6mm) Fitting

Regulator/Filter

Assembly

2-Stage Filter

Inlet Port (IN)

Outlet Port

(OUT)

Two Stage

Filter

Assembly

Art # A-07945_AC

Hose Clamp

Optional Two - Stage Filter Installation

Содержание A80 CUTMASTER



































































































































Результаты поиска

Содержание A80 CUTMASTER

Отзывы:

Thermal Dynamics A80 CUTMASTER, Руководство по эксплуатации, Страница: 31 / 130

Результаты поиска

Содержание A80 CUTMASTER

Отзывы: