Thermal Dynamics A80 CUTMASTER Скачать руководство пользователя страница 29

Страница: 29 / 130

A80

0-4985

INSTALLATION

3-3

5. Pass the cable being used through the access open-

ing in the back panel of the power supply. Refer to

Section 2 for power cable specifications.

CAUTION

The primary power source and power cable

must conform to local electrical code and the

recommended circuit protection and wiring

requirements (refer to table in Section 2).

6. Connect the wires as follows.

• Connect Bus Bar Jumpers on the contactor as

shown in prior illustration and on label in the

power supply.

• Green / Yellow wire to Ground.

7. With a little slack in the wires, tighten the through

- hole protector to secure the power cable.

8. Reinstall the Power Supply cover.

See "B. Cover Installation".

9. Connect the opposite end of individual wires to a

customer supplied plug or main disconnect.

10. Connect the input power cable (or close the main

disconnect switch) to supply power.

F. Connections to Three Phase Input Power

WARNING

Disconnect input power from the power

supply and input cable before attempting

this procedure.

These instructions are for changing the input power and or

cable on the 208/230, 400, 460 VAC Power Supply to Three

- Phase input power.

1. Remove the Power Supply cover.

See "A. Cover Removal".

2. Disconnect the original input power cable from the

main input contactor and the chassis ground con-

nection.

3. Loosen the through - hole protector on the back

panel of the power supply. Pull the original power

cable out of the power supply.

4. Using a customer supplied four - conductor input

power cable for the voltage desired, strip back the

insulation on the individual wires.

5. Pass the cable being used through the access open-

ing in the back panel of the power supply. Refer to

Section 2 for power cable specifications.

CAUTION

The primary power source and power cable

must conform to local electrical code and the

recommended circuit protection and wiring

requirements (refer to table in Section 2).

6. Connect the wires as follows.

• Wires to L1, L2 and L3 input. It does not matter

what order these wires are attached. See previ-

ous illustration and on label in the power supply.

• Green / Yellow wire to Ground.

7. With a little slack in the wires, tighten the through

- hole protector to secure the power cable.

8. Reinstall the Power Supply cover.

See "B. Cover Installation".

9. Connect the opposite end of individual wires to a

customer supplied plug or main disconnect.

10. Connect the input power cable (or close the main

disconnect switch) to supply power.

Содержание A80 CUTMASTER



































































































































Результаты поиска

Содержание A80 CUTMASTER

Отзывы:

Thermal Dynamics A80 CUTMASTER, Руководство по эксплуатации, Страница: 29 / 130

Результаты поиска

Содержание A80 CUTMASTER

Отзывы: