Thermal Dynamics A80 CUTMASTER Скачать руководство пользователя страница 108

Страница: 108 / 130

A80

SERVICE

0-4985

5T-2

5T.02 Inspection and Replacement of

Consumable Torch Parts

WARNING

Disconnect primary power to the system be-

fore disassembling the torch or torch leads.
DO NOT touch any internal torch parts while

the AC indicator light of the Power Supply

is ON.

Remove the consumable torch parts as follows:

NOTE!

The shield cup holds the tip and starter

cartridge in place. Position the torch with

the shield cup facing upward to prevent

these parts from falling out when the cup

is removed.

1. Unscrew and remove the shield cup from the torch.

NOTE!

Slag built up on the shield cup that cannot

be removed may effect the performance of

the system.

2. Inspect the cup for damage. Wipe it clean or replace

if damaged.

Art # A-08067

Shield Cups

3. On torches with a shield cup body and a shield

cap or deflector, ensure that the cap or deflector

is threaded snugly against the shield cup body. In

shielded drag cutting operations (only), there may

be an O-ring between the shield cup body and drag

shield cap. Do not lubricate the O-ring.

Drag Shield Cap

Shield

Cup Body

O-Ring No. 8-3488

Art # A-03878

4. Remove the tip. Check for excessive wear (indicated

by an elongated or oversized orifice). Clean or re-

place the tip if necessary.

Good Tip

Worn Tip

A-03406

Example of Tip Wear

5. Remove the starter cartridge. Check for excessive

wear, plugged gas holes, or discoloration. Check

the lower end fitting for free motion. Replace if

necessary.

Art # A-08064_AC

Spring-Loaded

Lower End Fitting

Full Compression

Spring-Loaded

Lower End Fitting at Reset /

Full Extension

6. Pull the Electrode straight out of the Torch Head.

Check the face of the electrode for excessive wear.

Refer to the following figure.

Worn Electrode

New Electrode

Art # A-03284

Electrode Wear

7. Reinstall the Electrode by pushing it straight into

the torch head until it clicks.

8. Reinstall the desired starter cartridge and tip into

the torch head.

9. Hand tighten the shield cup until it is seated on the

torch head. If resistance is felt when installing the

cup, check the threads before proceeding.

This completes the parts replacement procedures.

Содержание A80 CUTMASTER



































































































































Результаты поиска

Содержание A80 CUTMASTER

Отзывы:

Thermal Dynamics A80 CUTMASTER, Руководство по эксплуатации, Страница: 108 / 130

Результаты поиска

Содержание A80 CUTMASTER

Отзывы: