manualshive.com logo in svg

Thermal Dynamics A80 CUTMASTER, Руководство по эксплуатации, Страница: 104 / 130

Поделиться
Скачать
Thermal Dynamics A80 CUTMASTER Скачать руководство пользователя страница 104

A80

  

SERVICE 

0-4985

5-6

5.06  Power Supply Basic Parts Replacement

 

WARNING

Disconnect primary power to the system 

before disassembling the torch, leads, or 

power supply.

This section describes procedures for basic parts replace-

ment.  For more detailed parts replacement procedures, 

refer to the Power Supply Service Manual.

A.  Cover Removal

1.  Remove the upper and lower screws which secure 

the cover to the main assembly. Do not loosen the 

lower screws inside the cut out slots in the bottom 

of the cover.

Art # A-08429

Lower 

Screws

Lower 

Screws

Slots

Upper

Screws

2.  Carefully pull the Cover up and away from the unit.

B.  Cover Installation

1.  Reconnect the ground wire, if necessary.

2.  Place the cover onto the power supply so that slots 

in the bottom edges of the cover engage the lower 

screws.

3.  Tighten lower screws.

4.  Reinstall and tighten the upper screws.

C.  Filter Element Assembly Replacement

The Filter Element Assembly is in the rear panel.  For better 

system performance, the filter element should be checked 

per the Maintenance Schedule (Subsection 5.02), and either 

cleaned or replaced.  

1.  Remove power from the power supply; turn OFF the 

gas supply and bleed down the system.

2.  Remove the system cover.  See "A  Cover Removal" 

in this section. 

3.  Locate the internal air line and the fitting from the 

filter assembly.  Number 1 in the following illustra-

tion.

4.  Hold a wrench or similar tool against the locking 

ring on the filter assembly fitting, then pull on the 

hose to release it. (Numbers 2 and 3 in the following 

illustration).

Art # A-07989

1

2

3

4

5

6mm 

Содержание A80 CUTMASTER



































































































































Отзывы:

Нет отзывов