Thermador PRG486JDG/01 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 91

Thermador PRG486JDG/01 Скачать руководство пользователя страница 10

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models:

PRG486JDG/01, PRL486JDG/01

58300000159722_ARA_EN_D

Page 11 of 92

2.1.5

Temperature / Function Selector Knob for Small Oven

The Temperature/Function Selector Knob for the small oven enables
selecting a temperature from 150° F to 500° F, as well as one of the
oven function modes.

NOTE:

Warm setting displays “Warm’” which is about 150° to 175° F.

■

Rotate the outer dial to select a cooking mode, and then rotate the

inner knob to select the temperature.

2.1.6

Oven Light and Panel Light Switches

There is a toggle switch for each oven light, and for the panel light.

2.2 LED Indicators

When a burner is lit, its blue LED indicator is illuminated.

2.3 Automatic Re-Ignition

Each rangetop burner has its own electronic igniter that sparks when
the burner is turned on. If one or more burner blows out, the
respective igniter/electrode automatically re-ignites the flame.

2.4 Operation during a Power Outage

In Case of Power Outage

■

When there is a removal of electrical power, the XLO / XHI

burners and griddle/grill cannot be used. Do not attempt to light
them manually during a power outage.

■

If for any reason a control knob is on when there is any failure or

removal of electrical power from the appliance (such as a power
outage), immediately turn all control knob(s) to the

OFF

position.

■

Ventilate well by opening a door or window,

and wait at least

5

minutes for all the gas to dissipate.

■

If you smell gas, refer to the applicable safety precautions stated

in this manual, including the

Important Safety Information

section

on page

2.5 Rangetop Burner Assembly and Maintop

Components

Figure 3: Rangetop Burner Assembly and Maintop Components

1

Electrode (Igniter)

2

Burner cap

3

Burner base

4

Venturi tube

5

Burner pedestal

6

Jet holder assembly

7

Wire guard clip

8

Burner support rail

9

Heat shield

10

Maintop

«
...
8
9
10
11
12
...
»

Содержание PRG486JDG/01




























































































Отзывы:

Нет отзывов