manualshive.com logo in svg

THERMACUT EX-TRAFIRE 45HD, Руководство оператора, Страница: 69 / 80

Поделиться
Скачать
THERMACUT EX-TRAFIRE 45HD Скачать руководство пользователя страница 69

EX-TRAFIRE

®

45SD

Operator Manual, Revision T-5

9-69

Filter-EX Compressed Air Filter with replacement filter cartridge

EX-0-804-001 - Filter-EX Compressed Air Filter 

(Standard package 1 piece)

EX-0-804-002 - Filter-EX Air Filter Cartridge  

(Standard package 8 pieces)

Technical specification

Filtering Degree:

0�01 μinch – 0�25 μm

Maximum Pressure:

125 PSI – 8�5 bar

Maximum Flow @ 80%:

2700 SCFH – 1250 l/min�

Temperature Range:

15 – 140F / −10 +60 °C

Size Pipe:

¼ NPT

Dimension:

Ø 5�2“ × 7�9“ – Ø 132 × 200 mm

This filter does not fall under the specification of pressure equipment and requires no revision�

Advantages of using the Filter-EX Compressed Air Filter:

 

• 

 Removes solid particles, aerosols, and moisture from the compressed air� 

• 

 Elimination of the negative effects caused by humidity during cutting� 

• 

 Extends the service life time of the torch, leads and consumables� 

• 

 Reduces the risk of torch and power supply damage� 

• 

 Positive effect on the quality of the cut� 
 

SECTION 9: ACCESSORIES

SECTION 9�

ACCESSORIES:

The maximum pressure of this item does not match the 10�0 bar rating 
of the power supply�

Содержание EX-TRAFIRE 45HD

















































































Отзывы:

Нет отзывов