manualshive.com logo in svg

THERMACUT EX-TRAFIRE 45HD, Руководство оператора, Страница: 47 / 80

Поделиться
Скачать
THERMACUT EX-TRAFIRE 45HD Скачать руководство пользователя страница 47

EX-TRAFIRE

®

45SD

Operator Manual, Revision T-5

4-47

Machine torch consumables installation

WARNING 

Plasma arc is generated immediately 

when the CNC start signal is ON

Plasma arc is generated immediately when the CNC start signal is ON� 
The plasma arc will cut quickly through gloves and skin�  

Make sure the power supply is switched off before changing consumables�

1�  Insert the nozzle into the retaining cap�

2�  Insert the swirl ring into the 

assembly (retaining cap + nozzle)�

3�  Insert the electrode into the assembly 

(retaining cap + swirl ring)�

4�  Screw on this whole assembly (retaining cap +  

ele swirl ring) to the seat bottom of the torch and 
tighten by hand� Do NOT overtighten� 
The nozzle must seat properly without any movement�
If not, reasseble it and put these parts together again�

5�  Screw on the shield and tighten by hand�  

Do NOT overtighten�

 

  SHIELD 

       RETAINING CAP 

         NOZZLE 

  SWIRL RING 

     ELECTRODE 

 

TORCH

Cross - section 

of assembly�

Cross - section 

of assembly�

Cross - section 

of assembly�

Содержание EX-TRAFIRE 45HD

















































































Отзывы:

Нет отзывов