manualshive.com logo in svg

THERMACUT EX-TRAFIRE 45HD, Руководство оператора, Страница: 46 / 80

Поделиться
Скачать
THERMACUT EX-TRAFIRE 45HD Скачать руководство пользователя страница 46

EX-TRAFIRE

®

45SD

Operator Manual, Revision T-5

4-46

WARNING 

SPARKS AND HOT METAL CAN 

BURN THE SKIN AND EYES

When angling the torch for cutting, piercing or gouging, molten metal (Arc 
Spray) will occur in the direction that the torch is aimed� Aim the torch away 
from yourself and others�

Hold the torch so that the nozzle is within 1�5 mm of the work piece before firing�

Hold the torch at an angle of 45° to the work piece� 
Depress the trigger to start the pilot arc� Transfer the 
arc to the work piece

Maintain an approximate angle of 45° to the work 
piece�  
Maintain travel in the direction of the material to be 
removed� 

Direction of gouging

Gouging

Alignment of the machine torch FHT-EX

®

45TTM

Mount the machine torch perpendicular to the material to be cut, use a square to align the torch 
at 0 ° and 90 °, if torch alignment is not possible, check the cutting table for level to obtain a true 
vertical cut�

Содержание EX-TRAFIRE 45HD

















































































Отзывы:

Нет отзывов