manualshive.com logo in svg

THERMACUT EX-TRAFIRE 45HD, Руководство оператора, Страница: 37 / 80

Поделиться
Скачать
THERMACUT EX-TRAFIRE 45HD Скачать руководство пользователя страница 37

EX-TRAFIRE

®

45SD

Operator Manual, Revision T-5

4-37

1� Mode selection�

Grid cutting mode

 

To adjust the cutting current, press on the multifunction 
knob briefly to switch cutting mode� 
The current range is 20-45 A, the air pressure range is 4�2 - 5�6 bar�

Gouging mode

 

To adjust the cutting current, press on the multifunction 
knob briefly to switch cutting mode� 
The current range is 20-45 A, the air pressure range is 2�1 - 4�5 bar�

Cutting mode

To adjust the cutting current, press on the multifunction 
knob briefly to switch cutting mode� 
The current range is 20-45 A, the air pressure range is 4�2 - 5�6 bar�

Setting of power supply

The LCD screen contains two menus� 

In the first menu, the cutting current (Amperage) and the operation modes can be adjusted�  
Turn the regulator knob left or right to set cutting current� Press the multifunction knob briefly to set 
operation modes� 

In the second menu, the pressure value in bar, MPa or psi can be adjusted� Also display either: torch 
type, actual torch length and cutting voltage�

Hold down the multifunction knob for 1 second, the cutting parameters flash, the second menu has 
been activated� If there is no operation for 6 seconds, or hold down the multifunction knob for 1 
second again, the cutting current display flashes, it will switch back to the first menu�

All personal settings will be restored to factory settings when the system is switched off�

Содержание EX-TRAFIRE 45HD

















































































Отзывы:

Нет отзывов