THERMACUT EX-TRAFIRE 100SD Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 60

background image

EX-TRAFIRE

®

100SD

Operator Manual, Revision T-5

3-19

Power supply location

Place the plasma arc power supply EX-TRAFIRE

®

100SD on a flat even surface with a minimum

distance of 0�5 m of clear space all round to ensure good ventilation�

Mains power connection

The EX-TRAFIRE

®

100SD plasma arc power supply requires a 400 VAC ±15% three-phases mains

power source� Use a circuit breaker for power line input so that the operator can turn off the power
supply quickly in an emergency� Locate the switch so that it is easily accessible to the operator� The
interrupt level of the switch must be equal to or exceed the continuous rating of the fuses� Use slow
blow fuses with a suitable capacity in accordance with local and national electrical codes�

Connecting to an engine drive power generator

When using an engine drive generator to power the EX-TRAFIRE

®

100SD:

•

Engine drive operation;

1� Set engine drive output to three-phases AC�
2� Plug the EX-TRAFIRE

®

100SD mains power lead in to the power outlet�

3�  Hard wire connection (No plug fitted) should be performed by a certified electrician�
4�  Set the engine drive to maximum output (see chart below)�
5�  For optimum performance, do not share the engine drive with other equipment such as

welding plant, lighting systems or angle grinders�

Three-phases, 50/60 Hz, 400 VAC ±15%

Engine drive rating

Current output

EX-TRAFIRE 100SD Performance

25 kW

100 A

Full arc stretch

22�5 kW

100 A

Limited arc stretch

Grounding

To reduce electromagnetic interference (EMI) and to ensure personal safety and correct operation,
the EX-TRAFIRE

®

100SD must be properly grounded through the mains power lead in accordance

with local and national electrical codes of practice� The three-phases service must be of the 4-wire
type with a protective green-yellow wire for protective earth ground and must comply with national
and local electrical codes of practice�

«
...
17
18
19
20
21
...
»

Содержание EX-TRAFIRE 100SD





























































Отзывы:

Нет отзывов

Похожие инструкции для EX-TRAFIRE 100SD

Бренд: Makita Страницы: 110

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 26

Бренд: D-CUT Страницы: 6

Бренд: EINHELL Страницы: 96

Бренд: NARGESA Страницы: 36

Бренд: D-CUT Страницы: 6

Бренд: Silca Страницы: 2

Бренд: Darkly Labs Страницы: 77

Бренд: Ogura Страницы: 16

Бренд: Logan Страницы: 16

A Class Mark II

Бренд: Datamax Страницы: 14

Бренд: Ryobi Страницы: 148

Бренд: Mac allister Страницы: 48

Бренд: Vari Страницы: 36

Бренд: Tanaka Страницы: 17

Бренд: Paperfox Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды