Theben FCA 2 Скачать руководство пользователя

Страница: 6 / 89

Fan Coil Actuator FCA 2

Updated: Feb-16 (subject to changes) Page

1.2 Advantages of the FCA 2

•

Operating voltage 100-240 V 50/60 Hz.

•

Suitable for 0-10 V valves.

•

Optional internal or external temperature controller.

•

Can be used in 2- and 4-pipe systems.

•

Also suitable for 0-10 V fans.

•

Easy start-up via 2 push buttons for fan and heating/cooling mode.

•

Additional relay for heating/cooling can also be used as a switch output.

•

Change of operating mode by means of presence and window objects.

•

Adjustable direction of action of inputs.

•

Heating/cooling object addressable as per DPT 1.100 or inverted.

1.2.1 Special features

•

Control via external actuating value or with integrated room thermostat.

•

Additional relay C1 can also be controlled as switching actuator channel via the bus

•

Setpoint in cooling mode can be adjusted in relation to the outdoor temperature

•

E1 and E2 can be used as binary inputs if required.

Содержание FCA 2


























































































Результаты поиска

Содержание FCA 2

Отзывы:

Похожие инструкции для FCA 2

Бренды по названию

Популярные бренды

Theben FCA 2, Руководство пользователя

Результаты поиска

Содержание FCA 2

Отзывы:

Похожие инструкции для FCA 2

Бренды по названию

Популярные бренды