Theben FCA 2 Скачать руководство пользователя

Страница: 5 / 89

Fan Coil Actuator FCA 2

Updated: Feb-16 (subject to changes) Page

1.1 Operation and display

FCA 2 is fitted with 9 LEDs and 2 push buttons.

•

3 red LEDs for displaying fan stage/fan speed (see figure 1)

•

1 red LED for heating mode

•

1 blue LED for cooling mode

•

1 red LED for the additional relay (C1)

•

2 red LEDs for inputs 1 and 2 (E1, E2)

•

1 red LED for test mode

•

1 push button for fan stages/fan speed

•

1 push button for heating/cooling mode /

Figure 1: LEDs for displaying fan stages or fan speed

Fan stages (standard fan, 1-3 stages)

1-32 %

33-65 %

66-100 % Fan speed (0-10 V control)

By using the manual button, the fan stages can be switched one after another.

•

Standard fan control: Off



stage 1



stage 2



stage 3



Off



stage 1 etc.

•

0-10 V fan control: Off



33%



66%



100%



Off



33% etc.

Содержание FCA 2


























































































Результаты поиска

Содержание FCA 2

Отзывы:

Похожие инструкции для FCA 2

Бренды по названию

Популярные бренды

Theben FCA 2, Руководство пользователя

Результаты поиска

Содержание FCA 2

Отзывы:

Похожие инструкции для FCA 2

Бренды по названию

Популярные бренды