manualshive.com logo in svg

Thales ProtectToolkit 5.9.1, Руководство по установке и настройке

Поделиться
Скачать
Thales ProtectToolkit 5.9.1 Скачать руководство пользователя страница 75

Chapter 4:   ProtectToolkit Software Installation

If the compile fails, or the driver does not come up automatically (

hsmstate

fails), you will need to correct the

problem and then

cd /opt/ETpcihsm/src

and invoke

make(1)

as root. The

Makefile

in that directory has

some notes to help you get the driver compiled correctly.

To uninstall the PCie access provider manually

Use the

rpm(8)

command with the appropriate package name as a parameter.

# rpm -e PTKpcihsmK7

Signing the ProtectServer PCIe 2 Driver for UEFI Secure Boot

Red Hat Enterprise Linux 7 (RHEL 7) can be installed and run on systems where UEFI Secure Boot is enabled.
With Secure Boot enabled, the RHEL kernel requires all kernel modules, including device drivers, to be signed
by a key that is trusted by the EFI boot loader. If a module is not signed, it is prevented from loading at runtime
and the dependent device will not work.

To use ProtectServer PCIe 2 in a Secure Boot-enabled environment, the driver must be signed and trusted by
the OS and boot loader.

The following procedure includes:

>

Generating RSA signing keys and certificates

>

Signing the ProtectServer PCIe driver

>

Enrolling the signing public key into the system keyring

>

Loading the signed driver

NOTE

This procedure applies only to a CentOS 7 environment with UEFI Secure Boot

enabled. The steps have been tested on RHEL release 7.6.1810. The

mokutil

utility on

earlier versions of Red Hat might show inconsistent behavior. If you encounter problems,
upgrade your OS.

Steps may vary on other Linux platforms, but the general procedure is the same.

Prerequisites

>

UEFI Secure Boot must be enabled on the Linux system.

>

The ProtectServer PCIe 2 Access Provider must be installed.

The driver will fail to load and

service vkd status

may return

vkd is not running

.

System logs might display the error message

could not insert module vkd.ko: Required key not

available

. This appears because the driver module

vkd.ko

needs to be signed.

>

Driver signing requires that the following tools be available on the system:

Tool

Provided by
Package

Used on

Purpose

openssl

openssl

Build system

Generates public and private X.509 key pair

Thales ProtectServer HSM 5.9.1 ProtectServer HSM and ProtectToolkit Installation and Configuration Guide

2021-11-02 08:51:40-04:00 Copyright 2009-2021 Thales Group

75

Содержание ProtectToolkit 5.9.1































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды