Thales MissionLINK Certus 200 Скачать руководство пользователя | Manualshive

Страница: 9 / 61

background image

ix

Installation Guide 84465 Rev. H

Industry Canada Information

NOTE

Certus 350
Industry Canada: 473C-MF350BV
Contains IC: 473C-WROOM32U

NOTE

Certus 200
Industry Canada: 473C-MF200BV
Contains IC: 473C-WROOM32U

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.

This radio transmitter (473C-MF350BV or 473C-MF200BV) has been approved by Industry
Canada to operate with the antenna listed in Table 4-1 with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for
use with this device.

Le présent émetteur radio (473C-VF350BM ou

473C-MF200BV

) a été approuvé par Industrie

Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non
inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

«
...
7
8
9
10
11
...
»

Содержание MissionLINK Certus 200






























































Отзывы:

Нет отзывов

Похожие инструкции для MissionLINK Certus 200

Бренд: Rabe Страницы: 65

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: NARGESA Страницы: 33

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: GE Страницы: 698

Бренд: FJC Страницы: 2

Sonopuls HD 4050

Бренд: BANDELIN Страницы: 48

Бренд: CAMPAGNOLA Страницы: 4

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Madsen Страницы: 206

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: Qlight Страницы: 4

Бренд: olympia electronics Страницы: 4

Бренд: Yacht Devices Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды